v2.0 (1.0.2.0) (EN/F/E)
user manual
guide de l’utilisateur
manual de usuario
Product registration
RCD20
Thank you for purchasing an RCA product. We pride ourselves on the
quality and reliability of all our electronic products but if you ever
need service or have a question, our customer service staff stands
REGISTRATION: Registering On-line will allow us to contact you in
the unlikely event a safety notification is required under the Federal
Consumer Safety Act. Register Online at:
WWW.RCAAUDIOVIDEO.COM. Click on Product Registration and
Fill Out the Brief Questionnaire.
Enregistrement du produit
Merci d’avoir acheté un produit RCA. Nous sommes fiers de la qualité
et de la fiabilité de tous nos produits électroniques, mais en cas de
nécessité de réparation ou pour toute question, le personnel de
notre service clientèle est prêt à vous aider. Contactez-nous sur
www.rcaaudiovideo.com. ENREGISTREMENT D’ACHAT: Enregistrer votre produit en ligne nous permettra de communiquer
avec vous pour tout avis de sécurité au sujet du produit en vertu du Federal Consumer Safety Act (Loi fédérale de protection
du consommateur). Enregistrez votre produit en ligne sur: WWW.RCAAUDIOVIDEO.COM. Cliquez sur Enregistrement
produit et remplissez le court questionnaire.
Enregisregistro del productotrement du produit
Gracias por comprar un producto RCA. Nos enorgullece la calidad y fiabilidad de todos nuestros productos electrónicos, pero si
alguna vez necesita servicios técnicos o si tiene alguna pregunta, nuestro personal de atención al cliente está a su disposición
para ayudarle. Comuníquese con nosotros en www.rcaaudiovideo.com. REGISTRO DE COMPRA: El registro en línea nos
permitirá comunicarnos con usted en el caso de tener que enviarle algún aviso de seguridad en virtud de la Ley Federal de
Seguridad del Consumidor. Registre el producto en línea en: WWW.RCAAUDIOVIDEO.COM. Haga clic en Registro del
producto y responda al cuestionario.
EN/F/E
It is important to read this user manual prior to using your new product for the first time.
Nous vous recommandons de lire ce manuel d’instructions avant d’utiliser votre nouveau produit pour la première fois.
Es importante leer este manual antes de usar por vez primera su equipo.
General controls
Clock
Before you begin
Top view
Setting clock manually
Plugging in for power
Power failure indicator
1. Press and hold SET TIME to enter clock setting mode.
2. While holding down SET TIME, press HR to set the
hour.
•
•
Connect the power cord to a convenient wall outlet.
Once connected with power, the clock flashes. Refer to
the Clock section for instructions on properly setting the
Clock.
If you have not installed the 9-volt alkaline battery in the
product, or the battery runs out while power is interrupted,
all the settings (clock and alarm) will be lost. After AC power
is restored, the Digital Display will flash to indicate that
power was interrupted and you should readjust the time
settings.
•
The clock is in 12 hour format. The PM indicator will
appear for showing a PM time.
2. While holding down SET TIME, press MIN to set the
Battery back-up operation
minute.
•
This clock is equipped with a timekeeping system that
can be powered with a 9-volt alkaline battery (not
included). The power failure protection circuit will not
operate unless battery is installed.
3. Release SET TIME to confirm and exit clock setting
Note: It is recommended to replace the battery at least once
per year even if no power failures have occurred.
mode.
•
•
When normal household power is interrupted, the
battery will power the clock to keep track of time and
alarm settings programmed into memory.
When the battery backup functions, the digital display
will not light, however, the function of alarm still occurs
during the power interruption if remaining battery
power is adequate.
Normal operation will resume after AC power is
restored so you will not have to reset the time or the
alarm.
Alarm
Alkaline (NEDA 1604A/IEC 6LR61) type
battery is recommended. Carbon-zinc battery
may be used but memory holding time will
Setting alarm time
be substantially reduced. Memory holding
1. Press and hold SET ALARM to enter alarm setting
time for a fresh alkaline battery is approximately 8
hours (if alarm is not operated) which should take
care of short, nuisance-type AC power failures. To
preserve battery life, the unit should remain plugged
into an AC outlet. As the battery gets older, its
voltage drops and memory may be lost. Be sure to
replace the battery periodically. Battery should be
removed if the unit will be stored for more than one
month. A leaky battery can badly damage unit.
mode.
ALARM ON/OFF – Turn the alarm on/off
2. While holding down SET ALARM, press HR to set the
•
hour.
LIGHT ON/OFF – Used to illuminate the SNOOZE button
•
The clock is in 12 hour format. The PM indicator will
appear for showing a PM time.
HR – Adjust hour in clock setting mode or alarm setting
mode
2. While holding down SET ALARM, press MIN to set the
To install the battery:
minute.
1. Remove battery compartment door (located at the
bottom of the clock) by applying thumb pressure to the
tab on battery door and then lift the door out and off
the cabinet.
3. Release SET ALARM to confirm and exit alarm setting
MIN – Adjust minute in clock setting mode or alarm
setting mode
mode.
Turning on/off the alarm
1. Slide the ALARM ON/OFF switch to the ON position.
The AL indicator will turn on to show that the alarm is
on.
2. Slide the ALARM ON/OFF switch to the OFF position.
The AL indicator will turn off to show that the alarm is
off.
SET TIME – Enter clock setting mode
Battery
compartment
SET ALARM – Enter alarm setting mode
SNOOZE – Enter snooze mode where the alarm will quiet
but sound again once the snooze period is over
Ways to turn off alarm
•
To silence the wake function momentarily, press
SNOOZE. The alarm will be on again when the snooze
period (9 minutes) is over.
2. Connect a 9-volt alkaline battery (not included) to the
connector plug.
3. Replace the compartment door.
•
To disable the wake function completely, slide the
ALARM ON/OFF switch to the OFF position. The AL
indicator will turn off to show that the alarm is off.
Light
Slide the LIGHT ON/OFF switch to the ON position to
illuminate the light on the SNOOZE button.
|