Rosen Entertainment Systems Car Video System DA 7169 User Guide

 
Table of Contents  
1 Before You Begin ............................................ 2  
2 Installing the DA-7169 Monitor ....................... 4  
3 Parts Overview................................................. 8  
4 Operating the DA-7169 Monitor ................... 11  
5 Specifications ................................................ 16  
6 Appendix ........................................................ 17  
 
1 Before You Begin  
Welcome to the In-Dash DA-7169 Operating Guide. Before  
you begin, read the following warnings and notes carefully.  
Warning!  
To avoid serious harm or injury to you, others, the vehicle,  
or the remote control unit, follow the instructions below.  
To avoid short-circuiting the electrical system:  
When replacing a blown fuse, disconnect all power  
supplies and power off the unit. Be sure to use the correct  
replacement fuse.  
If the unit shows signs of overheating or malfunction,  
power off the unit and consult your dealer immediately.  
Do not open the unit; there are no serviceable parts  
inside.  
To avoid damaging the LCD panel:  
Do not drop the LCD display panel or subject it to direct  
impact.  
If the LCD panel breaks, avoid contact with any broken  
glass or leaking fluids. If you come into contact with these  
materials, flush and clean the affected areas with water.  
Seek medical attention immediately.  
This unit uses high-quality electronic components and is  
manufactured under a stringent quality-control system.  
Properly maintain the remote control unit to ensure optimal  
performance:  
Replace the batteries regularly. To avoid damage to new  
batteries, do not use new and used batteries at the same  
time. Battery life is six months.  
Use a soft, damp cloth (a lens cloth) to wipe dirt and  
fingerprints off the screen. Chemical solvents, cleaning  
agents, or corrosive detergents can cause irreparable  
damage.  
Page 2  
 
1 Before You Begin  
Do not drop metal or foreign objects between the display  
screen and enclosure. Doing so may impede the motor-  
ized tray and cause an electrical short.  
Important Notes  
When using the unit with a radio/TV tuner (model DA-2301),  
reception quality will vary with geographical location and  
climatic conditions.  
Forsafety, thisunitcanonly beactivatedwhenthe  
vehicle’s hand break is engaged. See your dealer for  
details.  
Do not install the screen where it may distract the driver.  
Avoid installing the display screen in direct sunlight or  
near hot air vents. Operating temperature for the display  
screen is 0oC to 60oC. If the internal temperature of the  
vehicle is extremely high, cool down the inside of the  
vehicle before operating the unit.  
Install the unit in a dry location, away from condensation.  
To avoid a fire hazard, use the correct fasteners and  
connecting cables during installation.  
The unit contains high voltages. To avoid electrical shock,  
do not open the unit; there are no user serviceable parts  
inside.  
See your authorized dealer if unsure how to proceed.  
Before installing this display system,  
ensure you are in compliance with  
local traffic rules and regulations.  
Page 3  
 
2 Installing the DA-7169 Monitor  
Precautions  
1 This unit should be installed by a qualified service techni-  
cian.  
2 This product is designed to operate with a 12-Volt,  
negative ground battery.  
3 Disconnect the ground wire from the battery terminal  
before connecting this unit to the electrical system.  
4 Other products or accessories may have wires that are  
color-coded similarly to those for this unit. Refer to the  
electrical diagrams of any other products before installa-  
tion of the unit to avoid making wrong connections.  
5 To avoid short-circuiting the electrical system, use proper  
insulation and fastening materials.  
6 Do not connect the unit’s yellow wire directly to the  
battery terminal. Connect the unit’s red wire to the ACC of  
the ignition switch. Failure to connect the red and yellow  
wires properly may drain the vehicle’s battery.  
7 To avoid damaging the unit, use only the accessories  
supplied with the unit.  
8 Do not install this product at an angle exceeding ±30°.  
9 Do not install this product in a position that may cause  
injury to passenger(s) during an accident.  
Page 4  
 
2 Installing the DA-7169 Monitor  
Electrical Connections  
Color Code  
Function  
Black  
Red  
Ground  
ACC  
Yellow  
Blue  
+12 V  
+12 V Out (Max 1 Amp)  
Page 5  
 
2 Installing the DA-7169 Monitor  
Signal Connections  
Color Code  
Grey /Yellow  
Black /Yellow  
Black/Black  
Orange/Brown  
Function  
Video 1 In  
Video 2 In  
Video Out  
Rear View Camera/Night Switch  
Signal  
Signal & ControlSignal & Control  
Page 6  
 
2 Installing the DA-7169 Monitor  
Typical Wiring Diagram  
The following is a typical wiring diagram for an In-Dash DA-  
7169 connected to model DVA-310x and a radio receiver with  
a 40-Watt, 4-channel power amplifier.  
Page 7  
 
3 Parts Overview  
Front Panel  
1
2
3
4
Mute (MUTE)  
Remote sensor  
Signal Source select (SRCE and CH / AV1 / AV2)  
Player select and Play/Pause (DISC & PLAY /  
PAUSE)  
5
AM/FM Radio select (BAND & AM/FM; when  
interfaced with DA-2301)  
OPEN / CLOSE  
Disc select +/- (DISC)  
Audio select (AUDIO)  
6
7
8
9
Repeat function (REP)  
7/8/9 Memory location (1 / 2 / 3 / 4 / 5 / 6)  
10  
11  
12  
13  
14  
15  
16  
Forward (>)  
Up volume control  
Backward (<)  
Function mode (SEL)  
Down volume control  
Degree of tilt (ANGLE)  
Display mode (WIDE)  
Page 8  
 
3 Parts Overview  
Remote Control Unit  
Frequently Used Buttons  
CHANNEL SELECT: Selects TV channels, disc title, or  
desired settings on the MENU screen.  
MODE: Selects the input video source. i.e. TV / AV1 / AV2.  
MENU: Displays menu screen of functions available.  
POWER: Open (ON) or close (OFF) the monitor enclosure.  
VIEWING ANGLE & DISPLAY MODE:  
Press once to activate angle adjustment function. While in  
this mode, press por q to set the tilt angle of the screen.  
Press and hold to activate display mode functions: ZOOM /  
CINEMA / NORMAL / FULL.  
Page 9  
 
3 Parts Overview  
Replacing the Battery  
1 Use a small coin to remove battery container from the unit.  
2 Remove old battery and insert new one. The positive sign  
(+) should face upward.  
3 Insert battery container into unit until it is securely in place.  
Precautions  
1 Properly dispose of used battery.  
2 Overheating the battery may cause an explosion or create  
a fire hazard.  
3 Remove used batteries from the battery container to prevent  
leakage.  
4 Prevent children from playing with the battery.  
Page 10  
 
4 Operating the DA-7169 Monitor  
Operating the In-Dash DA-7169 Color  
Display Monitor  
To take full advantage of the In-Dash DA-7169’s features,  
read these operating instructions before using the monitor.  
Note: The color and brightness of the LCD display screen is  
factory preset. To adjust picture quality, follow the instruc-  
tions in this guide.  
Ejecting and Opening the Display Monitor  
To eject/open the display monitor, press the OPEN /  
CLOSE button (#6 on the Front Panel Overview on page  
7) once. The display monitor will automatically eject from  
its DIN enclosure.  
Caution: To prevent damage to the driver motor and  
gear train, do not obstruct the movement of the  
monitor tray.  
If the ejection of the display monitor is stopped halfway,  
press the OPEN / CLOSE button once to return the  
monitor to the closed position. Press OPEN / CLOSE to  
activate the ejection process again until the monitor is  
fully extended.  
The display monitor returns to the closed position when  
the ignition is turned OFF or when pressing the OPEN /  
CLOSE button when the monitor is in the open position.  
Adjusting the Position of the Monitor  
Press the ANGLE + / - button (#15) to adjust the viewing  
angle of the monitor.  
Page 11  
 
4 Operating the DA-7169 Monitor  
Note: To prevent damage to the gear train, do not use force to  
adjust the display screen.  
The display monitor returns to the preset position whenever  
the system is turned ON.  
Selecting the Screen Size  
Press the WIDE button (#16) to change the screen size.  
There are four options:  
ZOOM: Picture is stretched vertically and horizontally.  
CINEMA: Picture is displayed with uniform enlargement  
horizontally.  
NORMAL: When 4:3 picture is played on a wide screen,  
black bands appear on both side of the picture.  
FULL: 16:9 picture is fully displayed on screen.  
Adjusting Features of the Display Monitor  
Press the SEL button (#13) to scroll through the following  
screen options:  
COLOR: Color adjustment  
CONTRAST: Contrast setting  
BRIGHT: Brightness setting  
TINT: Color saturation  
DIMMER: When set to ON, the brightness of the screen  
adjusts automatically when vehicle headlights are turned  
ON.  
REV VID: (Reverse Video) ON or NORMAL. When set to  
ON, reverse video automatically runs when monitor is  
connected to a rear view camera.  
RESET: Resets COLOR, CONTRAST, BRIGHT and TINT  
Page 12  
 
4 Operating the DA-7169 Monitor  
to factory defaults.  
Note: The SEL button will have different functions when the  
monitor is connected to model DA-2301. Refer to the user  
manual for details.  
Once the correct option is visible, press the forward/  
backward keys (< and >) to confirm your selection. If no  
key is pressed, then the SEL mode will turn off in about  
five seconds.  
Choosing NTSC or PAL Display System  
Once input video source (TV / AV1 / AV2) is selected by  
pressing SRCE (#3), use the forward/backward keys (<  
and >) to toggle between NTSC or PAL display system.  
Note: The function of the forward/backward keys (< and >)  
changes when this monitor is connected to model DA-2301 or  
DVD player DVA-310x. Refer to the respective manuals for  
details.  
Adjusting the Volume  
When the monitor is connected to DA-2301, use the UP /  
DOWN keys (#11 & 14) to adjust the volume.  
Note: Refer to the DA-2301 user manual for details.  
Muting the Volume  
Press the MUTE button (#1).  
Note: This button is only activated when the monitor is  
connected to model DA-2301. Refer to the DA-2301 user  
manual for details.  
Page 13  
 
4 Operating the DA-7169 Monitor  
Selecting the Video Source  
Press the SRCE button (#3) to choose between AV1 and  
AV2.  
Note: Refer to Choosing NTSC or PAL Display System on  
previous page.  
Note: The SRCE button activates TV (CH) mode when the  
monitor is connected to model DA-2301.  
Selecting the Audio Channel  
Use theAUDIO button (#8) to select the desired channel  
when the monitor is connected to a DVD player or VCD/  
CD changer (model DA-2301).  
The AUDIO button is also used to select the audio lan-  
guage as recorded in the DVD.  
When playing back VCD, use theAUDIO button to toggle  
between AUDIO LL, AUDIO RR, or AUDIO STEREO.  
Note: Refer to the respective user manuals for details.  
Playing and Pausing the Disc Player  
When the monitor is connected to a DVD player or VCD/  
CD changer via model DA-2301, press the PLAY/PAUSE/  
DISC key (#4) to turn on the disc player, play the disc,  
and pause the disc player.  
Turning On and Changing the Radio Station  
When the monitor is connected to the DA-2301, press the  
BAND button (#5) to turn ON the radio and play the last  
selected channel.  
When the radio is ON, press the BAND button to toggle  
between radio bands (AM, FM1, FM2, FM3).  
Page 14  
 
4 Operating the DA-7169 Monitor  
Selecting Preprogrammed Radio Stations  
When the monitor is connected to model DA-2301, Use  
buttons 1 / 2 / 3 / 4 / 5 / 6 (buttons #7-9 on the Front  
Panel Overview on page 7) to select preprogrammed  
radio stations.  
Note: Refer to the DA-2301 user manual for details.  
Selecting a Disc to Play  
When the monitor is connected to a DVD or VCD/CD multi-  
disc player via model DA-2301, press the disc selection  
key (#4) to select the disk you wish to play.  
Using the Play Back Feature  
Press the REPEAT button (#9) to activate the play back  
feature and selection from the following options: OFF,  
CHAPTER, and TITLE.  
Page 15  
 
5 Specifications  
Specifications  
Monitor Display System: 7 in. (18 cm) Active Matrix Color  
LCD Display; NTSC/PAL selectable  
Display Format: 112,320 pixels  
Resolution: 336,960 dots / 1,440 (W) x 234 (H) dots  
Aspect Ratio: 16:9  
Active Area: 155.5 mm (W) x 87.8 (H) mm  
Front Panel: Anti-glare glass  
Back Light: 10,000 hours normal operation  
Mechanism: Fully Motorized Open/Close  
ViewingAngle:Adjustable Up/Down; Off-axis ViewingAngle  
(<) 120°  
Master Control: TV/AM/FM (DA-2301) and CD/VCD/DVD  
(DVA-310x) interfaces  
Source: Composite video input x 2; Composite video  
output x 1  
Operating Voltage: 12-Volt DC  
Operating Current: 1.5 Amp (Nominal)  
Mounting: Single DIN/In-Dash mount  
Weight: 1.8 kg  
Dimensions: 17.8 cm (W) x 18.5 cm (D) x 5.0 cm (H)  
All specifications are subject to change without prior notice.  
Page 16  
 

Razor Bicycle Accessories 25143060 User Guide
RCA Telephone 26925A User Guide
RIDGID Metal Detector Metal Detector User Guide
Roland Electronic Keyboard EXR 7 User Guide
Rosewill Refrigerator RCX Z755 EX User Guide
Sanyo Projector PLC SU51 User Guide
SATO Network Card GL 4xxe Series User Guide
Scag Power Equipment Lawn Mower STT 31BSG User Guide
Sears Lawn Mower 917257552 User Guide
Sennheiser Headphones HD 340 User Guide