Rosen Entertainment Systems VCR CV6825 User Guide

 
Frequently Asked Questions  
Table of Contents  
Frequently Asked Questions  
Why don’t I hear ClearVue sound over my radio?  
Quick Reference .................................................................. 3  
Lowering the Screen  
Try both 89.1 FM and 88.7 FM on your radio dial, and make  
sure that the FM Modulator is on by pressing and releasing the  
“SPEAKER ON/OFF” button on the remote until “FM ON” is  
displayed on the screen.  
Watching a Video  
Listening Over Vehicle Speakers  
Using Other Video Sources  
Watching TV  
Why doesn’t the TV button on the remote turn on the  
TV Tuner?  
About the ClearVue 6825 VCR System ............................... 4  
Operating the System.......................................................... 5  
Precautions .................................................................... 5  
Switching On .................................................................. 5  
Lowering the Screen ....................................................... 5  
Front Panel Controls ....................................................... 6  
Using the VCR................................................................ 6  
Using the Headphones.................................................... 6  
Using the Car Speakers .................................................. 8  
Using the TV Tuner ......................................................... 8  
Remote Control Reference ................................................. 9  
Basic Remote Functions .............................................. 10  
Changing View Settings ................................................ 11  
Using Auxiliary Sources .................................................... 12  
Frequently Asked Questions ............................................. 13  
Important Safety Notices................................................... 14  
Some buttons on your ClearVue remote are for other Rosen  
systems and products. Press the MODE button to turn the TV  
Tuner on with your system.  
How do I change channels on the TV Tuner?  
Press the PREV TRK and NEXT TRK buttons on the remote.  
Why did the headphones stop working?  
Check the power switch and the volume control. Check the  
MUTE button on the remote. Then try adding new batteries.  
Why did the remote stop working?  
Direct remote towards the black oval above the monitor when  
pressing buttons. Then try adding new batteries.  
Why has picture quality worsened with the VCR?  
The VCR probably needs cleaning with a head cleaning kit.  
Why do I have poor ClearVue sound quality sometimes  
over the speakers?  
You may be in an area that has a strong radio signal at the  
same FM frequency as the FM Modulator. See your Rosen  
dealer to have the ClearVue FM frequency reset.  
Page 13  
Rosen Products  
 
Quick Reference  
Using Auxiliary Sources  
Using Auxiliary Sources  
Quick Reference  
Release button  
The ClearVue 6825 includes auxiliary audio/video inputs that  
enable you to attach an external source device such as a video  
game or camcorder. You can also listen to an external audio  
source such as an MP3 player, portable CD player, or MiniDiscTM.  
To power on the system:  
Turn ignition switch to Run or ACC  
position.  
These inputs are standard RCA connectors. One set of connectors  
is on the VCR front panel and the other set is on the rear panel.  
Press the release button, as shown.  
The screen powers on automatically.  
Note: Before attempting to use any auxiliary source, be sure you  
have the appropriate cable to connect to the VCR system.  
To watch a video tape:  
To connect the auxiliary device to the VCR RCA jacks:  
1 Connect the right channel audio to the red jack.  
2 Connect the left channel audio to the white jack.  
3 Connect the video to the yellow jack.  
1 Power on the system.  
2 Point the remote at the screen and press the POWER  
button to turn on the VCR.  
3 Insert a video tape into the VCR. Playback begins.  
To listen over the vehicle speakers:  
Note: When using a non-battery operated auxiliary source (video  
game, or other) in a vehicle, a 12VDC/110VAC power inverter  
is required.  
1 Power on the system.  
2 Turn on the vehicle radio and tune it to 88.7 FM.  
To play an auxiliary device:  
1 Power on the device.  
3 Press SPEAKER ON/OFF on the remote until FM ON”  
appears on the screen.  
4 If you hear no audio, try tuning the radio to 89.1 FM.  
2 Press MODE on the remote until “LINE 2” appears on the  
screen.  
To use another video source:  
(such as an optional video game or camcorder)  
1 Connect the RCA audio and video outputs of the device  
to the Line Inputs on the front of the VCR.  
2 Press MODE on the remote until “LINE 2” appears on the  
screen. The Line 2 video image appears on the screen.  
To watch broadcast television:  
1 Press MODE until “CH___” and the current channel number  
appear on the screen (for example, “CH 2”).  
2 Press the up and down arrow buttons on the remote to  
change channels.  
Page 3  
Rosen Products  
ClearVue 6825 VCR System Owners Manual  
Page 12  
 
Remote Control Reference  
About the ClearVue 6825 VCR System  
Changing View Settings  
About the ClearVue 6825 VCR System  
To adjust settings for color, contrast, brightness, or tint:  
Welcome to the ClearVue 6825 VCR System Owner’s Manual.  
The ClearVue 6825 includes the following components:  
1 Press VIDEO MENU on the remote. The following menu  
appears in the screen.  
Overhead Monitor  
***MENU***  
Video Cassette Recorder (VCR) with TV Tuner  
Wireless IR Headphones (2 pair)  
Wireless IR Transmitter Dome  
Remote Control  
(32)  
(32)  
(32)  
(32)  
COLOR  
CONTRAST  
BRIGHT  
TINT  
FM Modulator (enables the video sound to be  
2 Press the up and down arrow keys on the remote to highlight a  
menu option. Each menu option has a range of values from 0 to  
63, with 32 as the default.  
heard over your vehicle’s speakers)  
Vehicle Trim Ring  
3 Press the left arrow key on the remote to reduce a setting.  
4 Press the right arrow key on the remote to increase a setting.  
5 Press EXIT on the remote to close the menu.  
Other parts and cables which are installed out of sight in  
your vehicle  
Note: The ClearVue 6825 VCR system is intended to be used  
with your ignition key switch in the Run or Acc position.  
Extended use of the system without the engine running  
should be avoided, as it could drain the battery.  
ClearVue 6825 VCR System Owners Manual  
Page 4  
Page 11  
Rosen Products  
 
Operating the System  
Remote Control Reference  
Basic Remote Functions  
Operating the System  
Point the remote control toward the overhead monitor.  
To view a video tape at a slower speed, press SLOW.  
To rewind a video tape, press REW.  
Precautions  
Use this system only after proper installation by a qualified  
installer.  
To fast forward a video tape, press FFWD.  
To pause or resume playback, press PLAY/PAUSE.  
To stop playback, press STOP.  
If the internal temperature of the vehicle is extremely high,  
allow a short cooling down period before operating the unit.  
If the unit shows signs of overheating or malfunction, power  
off the unit and consult your dealer immediately.  
To eject the video tape, press EJECT.  
Do not open the unit; there are no serviceable parts inside.  
Remote Control Battery Replacement  
Note: The VCR is sensitive to extreme temperatures and  
excess moisture. When the DEW/HEAT indicator on the  
face of the VCR illuminates, the VCR is unable to load a  
video tape, and the TV tuner is inoperable. If this occurs,  
wait until the temperature returns to a normal range and  
any moisture condensation has had time to evaporate  
before using the system.  
The ClearVue system remote requires twoAAAbatteries. Replace  
the batteries as shown below.  
Switching On  
Use the system when your vehicle is running or the ignition  
switch is in the “accessory” position.  
To avoid a dead battery, do not use the system for long  
periods of time without the engine running.  
Lowering the Screen  
To lower the screen, press the release button on the overhead  
monitor, as shown. The screen will lower into the viewing  
position.  
To adjust the viewing position, insert two fingers into  
the adjustment knob and rotate as needed.  
Release button  
Adjustment knob  
ClearVue 6825 VCR System Owners Manual  
Page 10  
Page 5  
Rosen Products  
 
Remote Control Reference  
Operating the System  
Remote Control Reference  
Front Panel Controls  
Video Cassette Tape Door  
The ClearVue remote control includes the following features. Only  
the buttons labeled below are active with this system.  
Video Menu  
Power  
Eject  
Mode  
Aux  
Mute  
VCP  
Play  
Stop  
Line 2  
(aux)  
Inputs  
Power  
Button  
Indicator Lights for  
Power, Recording,  
SLP, and Heat/Dew  
Modes  
Eject  
Rewind  
Fast  
Forward  
Record  
Speaker On/Off  
Menu  
Adjustment  
Menu  
Adjustment  
Using the VCR  
To view a video cassette tape:  
1 Power on system  
Exit  
2 Insert the cassette tape into the VCR. The tape begins playing  
and video appears on the screen.  
Next Track  
(Channel Down)  
Previous Track  
(Channel Up)  
Using the Headphones  
Play/Pause  
Channel  
Adjustments  
IR  
Menu  
Transmitter  
Dome  
Fast Forward  
Stop  
Rewind  
Slow  
Using the headphones with your system allows rear-seat  
passengers to listen to their VCR or video game without disturbing  
front-seat passengers. When using the headphones the IR  
transmitter dome must have a direct line of sight to the  
headphones to work properly.  
Page 9  
Rosen Products  
ClearVue 6825 VCR System Owners Manual  
Page 6  
 
Operating the System  
Operating the System  
Using the Car Speakers  
The system comes with two wireless IR headphones that receive a  
signal from the IR transmitter dome near the overhead console.  
To listen to system audio through your car speakers:  
1 Power on system.  
2 Insert a video cassette tape.  
3 Turn on the car radio.  
4 Tune the car radio to the FM frequency 88.7; this is the default  
system frequency.  
If audio from the system does not play over the car speakers:  
Volume  
Power LED  
Power ON/OFF  
1 Press SPEAKER ON/OFF on the remote control until “FM ON”  
appears on the screen.  
and /or  
To turn the headphones on and off, push the Power ON/OFF  
button on the right ear piece. The Power LED on the left ear piece  
indicates when headphone power is on. Power shuts off  
2 Tune the radio to 89.1 FM. This is an alternate system fre-  
quency.  
automatically after 3 minutes of no audio to preserve battery life.  
To turn off audio over the car speakers, press SPEAKER ON/OFF  
on the remote.Audio from the system is then available over the  
headphones only.  
To adjust the headphone volume, rotate the thumb wheel switch on  
the headphones.  
Note: Leaving the system to SPEAKER ON mode will reduce the  
performance of normal radio reception. To receive the  
best reception, always turn the system to SPEAKER  
OFF when not in use.  
The wireless IR headphones require twoAAAbatteries. To replace  
the batteries, remove the battery compartment cap on the right  
earpiece and insert batteries, as shown.  
Using the TV Tuner  
To view television:  
1 Power on the system.  
2 Press MODE on the remote control until “CH __” appears on  
the screen where __ is the current channel (“CH 2” for ex-  
ample).  
3 Press PREV TRK or NEXT TRK on the remote to change  
channels.  
Note: Broadcast television reception varies with location, terrain,  
distance from the broadcast tower, and other factors. Signal  
quality is likely to vary in a moving vehicle.  
Page 7  
Rosen Products  
ClearVue 6825 VCR System Owners Manual  
Page 8  
 

Renesas Computer Hardware H8S 2214 Series User Guide
Renesas Stereo System SH7709S User Guide
Rosewill Network Card RNWA PoE 100 User Guide
Ryobi Saw C2600 User Guide
Samsung Camcorder D230i User Guide
Samsung Computer Monitor 204BM User Guide
Samsung Microwave Oven G2711N User Guide
Samsung Projection Television SP50L6HD User Guide
Sanyo Projector POA PN01 User Guide
Scag Power Equipment Lawn Mower SFZ User Guide