B W CCD CAMERA
INSTRUCTION MANUAL
BW-4302 SERIES
[
]
SALES NETWORK
· SAMSUNG TECHWIN CO., LTD
·
SAMSUNG OPTO-ELECTRONICS AMERICA INC.
40 SEAVIEW DIRVE, SECAUCUS N.J
07094, U.S.A.
OPTICS & DIGITAL IMAGING DIV.
145-3, SANGDAEWON 1-DONG, JUNGWON-GU,
SUNGNAM, KYUNGKI-DO, KOREA
462-121
TEL : 209-902-0347
FAX :201-902-9342
TEL : 82-031-740 -8137~41
FAX: 82-031-740 -8145
P/ NO. : 6806-0344-01A
·
·
·
Printed in Korea
crecom 01.11
SAMSUNG CCD CAMERA
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING- TO PREVENT RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS CAMERA TO RAIN OR MOISTURE.
CAUTION :
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK),
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
INFORMATION-This equipment has been tested and found to
comply with limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
The lightning flash with arrowhead symbol, within
an equilateral triangle is intended to alert the user to
the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will required
to correct the interference at his own expense.
WARNING- Changes or modifications not expressly approved
by the manufacturer could void the user’s authority to operate
the equipment.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use other than specified power source.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service
person and should conform to all local codes.
B W CCD CAMERA
5
4
B W CCD CAMERA
Features
Contents
Electronic Iris
Automatic Backlight Compensation
PRECAUTIONS ........................................................................ 6
Electronic iris shutter is automatically
controlled at the speed of
1/60~1/100,000sec (EIA models),
1/50~1/100,000sec (CCIR models).
The backlight compensation technology allows
the camera to find the best picture conditions
in any environment and automatically gives a
necessary light level compensation, so that you
can always obtain the clear picture, the finest
detail and perfect light contrast.
GETTING TO KNOW YOUR CAMERA..................................... 7
Front ....................................................................................... 7
Back ........................................................................................ 8
Accessories ............................................................................ 9
Bottom .................................................................................... 10
Video/DC Selection Switch
The camera accepts 2 types of auto lris lenses
(DC type/Video type) and is set with Video/
DC selection switch.
CONTROLS AND ADJUSTMENTS........................................... 11
High Resolution
CONNECTION .......................................................................... 14
Installing Auto IRIS Lens ........................................................ 14
Installing C-Mount Lens .......................................................... 16
Installing CS-Mount Lens ........................................................ 17
Connecting To Monitor ........................................................... 18
Connecting To Power .................................................... 19
The horizontal resolution of 570 TV lines can be
achieved by using a high density CCD
having effective 410,000 pixels, which
SYNC. System
provides clean, noiseless and reliable pictures.
You can select INT(Internal Synchronization)
mode or L. L(Linelock Synchronization) mode.
TROUBLESHOOTING .............................................................. 20
SPECIFICATIONS .................................................................... 21
6
B W CCD CAMERA
B W CCD CAMERA
7
Precautions
Do not install the camera in extreme
temperature conditions.
Do not install or use the camera in an
environment where the humidity is high.
Do not drop the camera or subject
them to physical shocks.
Never keep the camera face to strong
light directly.
Do use the camera under conditions where
temperatures are within -10°C to 50°C.
Especially be careful for ventilation under
high temperature.
It can cause the image quality to be poor.
It can cause malfunctions to occur.
It can damage the CCD.
Do not expose the camera to rain or
spill beverage on it.
Do not touch the front glass of the
camera.
Do not install the camera under
unstable lighting conditions.
Never use the camera close to a
gas or oil leak.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode
the electronic components.
It is one of the most important parts of camera.
Be careful not to be stained by fingerprint.
Severe lighting change or flicker can cause the
camera to work improperly.
It can cause malfunctions to occur.
Do not disassemble the camera.
Notes:
•
•
If the camera is exposed to spotlight or object reflecting the strong light, smear or
blooming may occur.
Please check the power whether it satisfies the normal specification before connecting
the camera.
There are no user-serviceable parts
inside it.
8
B W CCD CAMERA
B W CCD CAMERA
9
Getting to Know Your Camera
Getting to Know Your Cam era
Front
Bottom
2
C -Mount Lens Adapter
1
Glass Protecting Cap
Tripod Mounting Hold
Used to install the camera on an optional tripod.
The tripod must be equipped with the screw
specified as shown below
4
Back Focus
Lock Screw
1/4″-20 UNC (20 THREAD)
L : 4.5mm± 0.2 mm (ISO standard),
or 0.197″(ASA standard)
L
3
CS-Mount Lens Adapter
You can remove and install this bracket on the top
of the camera.
You must use the supplied screw or the equivalent
(within 5mm). If not, it can cause malfunction and
demage inside the camera.
10 B W CCD CAMERA
B W CCD CAMERA
11
Getting to Know Your Camera
Getting to Know Your Camera
Back
Accessories
IRIS Mode
Selection Switch.
Video Out Jack
IRIS lens plug
BLC Function select Switch
Auto Iris Lens Connector
LEVEL Adjustment V.R
(Using DC Iris Lens Only!)
L-Wrench
SYNC Mode selection switch
Power Input Terminal
Notes: Each model has the different
power source.
Notes:There is no Sync selection
switch on the rear of DC
power type.
V.PHASE Adjustment V.R
Notes: There is no V.PHASE VR
on the rear of DC power type.
Instruction
Manual
High Voltage type
(4302CH)
12 B W CCD CAMERA
B W CCD CAMERA
13
Controls and Adjustments
Controls and Adjustm ents
Glass Protecting Cap
SYNC Mode Selection Switch
Be sure to cap the lens mount when the lens is not mounted. Pull out the
Used to choose INT or LL mode.
cap to remove.
SYNC (Synchronization) Mode
INT(Internal) mode : The camera may be operated independently with its
internal crystal control.
C-Mount Lens Adapter
Used to mount a C-mount lens. Remove it to mount a CS-mount lens. Turn
counterclockwise to remove.
LL(Linelock) mode : It synchronizes the video signal between cameras using
the frequency of the AC power supply without external
synchronous generator.
CS-Mount Lens Adapter
Used to mount a CS-mount lens. C-mount lenses can be used when the
C-mount adapter is attached, and CS-mount lenses can be used when it is
removed.
Notes :
The LL mode can be used in the areas of 60Hz(EIA models) and
50Hz(CCIR models).
There is no SYNC selection switch on the rear of DC power type.
Back Focus Lock Screw
V. PHASE Adjustment V. R
Used to readjust backfocus of the camera. There are two backfocus lock
screws. These must be loosened before the camera may be back
focused. Loosen lock screw using the L-wrench to turn the CS-mount lens
adapter, and tighten the lock screw after adjustment.
If camera is to be used in the LL mode, the vertical phase may require
adjustment to synchronize the vertical phase of the camera with other
camera in the system.
Make this adjustment when the vertical phase of the camera does not
match with other cameras or systems. For correct adjustment, use a multi-
channel oscilloscope. The V adjustment has been set at 180 degrees
and can be readjusted in the range of 0 to 270 degrees.
Tripod Mounting Hole
This screw hole is used to install the camera on a mount. The camera can
be installed on a tripod or other camera mount either from the top or the
bottom by using the 1/4” - 20UNC threaded holes in the camera. For
details, see page 11.
Notes :
This adjustment is necessary only when line lock sync operation is
performed.
There is no V. PHASE V.R on the rear of the DC power type.
Video Out Jack
Connect to the video input connector of monitor. This jack outputs a
composite video signal. Use a coaxial cable for connection.
Power Input Terminal
Used to connect AC/DC power source. For details, see page 23.
Notes : Each model has the different power source, you must confirm
appropriate power source of your camera.
Auto lris Lens Connector
Used to connect auto iris lens plug. Be sure to use video-drive auto iris
lens that operates on DC 12V and requires 40 mA or less. For details, see
page 18.
Level Adjustment V. R (Using DC Iris Lens Only!)
Used to adjust video output level. When the brightness control of the
monitor does not operate correctly, you can get the optimum picture by
controlling the Video output level of camera.
14 B W CCD CAMERA
B W CCD CAMERA
15
Controls and Adjustments
MANUAL LENS
Monitor picture
To make it brighter
To make it darker
Adjustment direction
Turn clockwise
Turn counterclockwise
When manual lens is mounted, two modes are available.
In VIDEO or DC mode, electronic shutter is fixed in “1/60” sec(EIA models),
“1/50” sec(CCIR models).
In ESC mode, electronic shutter is automatically controls the shutter speed
from “1/60” to “1/100,000” sec(EIA models), “1/50” to “1/100,000” sec(CCIR
models).
Notes : This function is activated when being in the ESC mode.
BLC(Backlight Compensation) Function CENTER/FULL Switch
This switch improves an image that is darkened because of backlighting.
This Function be possible only when the camera have a manual lens.
When the lighting source is in the rear of object, the object might be
seen some darkness. If you want to see object clearly, turn this switch
Center or Full the following diagram:
Notes : ESC (Electronic Shutter Control)mode : Electronically controls
optimal shutter speed.
Center emphasis
Full emphasis
IRIS Mode Selection Switch
Used to choose DC/VIDEO or ESC mode according to the type of your
lens.
USING AUTO IRIS LENS
You can choose DC or VIDEO mode according to the type of the lens.
In this case, electronic shutter is fixed in “1/60” sec(EIA models),
“1/50”sec(CCIR models).
B W CCD CAMERA
16 B W CCD CAMERA
17
CONNECTION
Connection
3. Remove the cover from the connector pin supplied, and
solder the lens cable to the connector pin as shown
Lens
Lens is not supplied with this camera. Purchase a lens suitable for
your environment. This camera accepts auto iris lens, both C- and
below.
• Video type :
CS-mount lens.
No. 1 Pin --- Red (Power source, DC 12V, 40mA MAX)
No. 2 Pin --- N.C
No. 3 Pin --- White (Video signal)
No. 4 Pin --- Black (GND)
• DC type:
Notes:
If the lens is stained with fingerprint or something, the image quality
might be poor.
No. 1 Pin --- Damping
-
It is recommended to use a high quality lens to improve the image
quality under low illumination.
No. 2 Pin --- Damping +
No. 3 Pin --- Drive +
No. 4 Pin --- Drive
-
Installing Auto Iris Lens
Cover
Lens cable
1. Peel the end of lens cable outer cover approximately 8mm. (5/16inch)
No. 3 Pin
No. 1 Pin
approx.
8 mm(5/16inch)
connector
No. 4 Pin
No. 2 Pin
4. Remove the protecting cap, and attach the lens into the
camera by turning clockwise.
2. Peel the end of the cable inner cover approximately 2mm. (1/16inch)
approx.
2 mm(1/16inch)
B W CCD CAMERA
18 B W CCD CAMERA
19
CONNECTION
CONNECTION
5. Connect the lens plug to the auto iris connector on the
rear of the camera.
Installing CS-M ount lens
1. Remove the protecting cap and C-mount adapter.
6. Set the IRIS Mode selection switch to Video according
to the type of the lens.
C-Mount Lens Adapter.
Glass Protecting Cap.
2. Attach the lens into the camera by turning clockwise.
Installing C-M ount lens
After removing the protecting cap, attach the lens into the
camera by turning clockwise.
Notes:
• Use the lens under the specification aside.
• Otherwise the lens can damage the camera
or abnormal fixing may be resulted in.
• A heavy lens may disturb the balance with
C-mount lens : 14 mm or less
the camera and possibly results in damage.
CS-mount lens : 9 mm or less
Don't use more than 450g lens.
• It is recommended to set the lens ALC mode to Av mode
(Average). Pk mode can be occurred hunting.
C-Mount Lens Adapter.
B W CCD CAMERA
20 B W CCD CAMERA
21
CONNECTION
CONNECTION
Connecting to Power
Connecting to M onitor
Each model has the different power source and the operation
characteristics.
Make sure the power is supplied to the appropriate power terminals
on the camera. Connect the power as referred on the following
figures.
Connect the VIDEO out jack to the monitor video in jack.
Monitor
CCD Camera
AC24V, 60Hz : BW-4302EA
AC24V, 50Hz : BW-4302CA
• As a connecting method varies according to instruments,
refer to the manual supplied with the instrument.
• Connect the cable after power is turned off.
• Set the 75Ω /Hi-Z selection switch as shown below if you
have intermediate device.
AC230V , 50Hz : BW-4302CH
Intermediate
VIDEO
VIDEO
75
Hi-Z
75
Hi-Z
Notes:
• Be sure to connect power cord after you finish installation.
• Check whether the frequency of power is 60Hz to use the linelock(L.L) mode in EIA models.
• Check whether the frequency of power is 50Hz to use the linelock(L.L) mode in CCIR models.
IN
OUT
IN
OUT
CCD Camera
End monitor
22 B W CCD CAMERA
B W CCD CAMERA
23
Specifications
Troubleshooting
If you have trouble operating your camera, refer to the following. If
the guidelines do not enable you to solve the problem, contact an
authorized technician.
ITEM
BW-4302EA
AC24V, 60Hz
4W
BW-4302CA
AC24V, 50Hz
4W
BW-4302CH
AC230V, 50Hz
4W
Problem
Solution
POWER SOURCE
POWER CONSUMPTION
Nothing appears • Check that the power cord and line connection
on the screen.
between the camera and monitor are made properly.
• Check that the VIDEO/ESC selection switch on the
rear of the camera set to a proper position according
to the type of your lens.
INT/Linelock
seclectable
(Phase: 0~270
Power frequency:
60Hz only)
INT/Linelock seclectable
(Phase: 0~270 Power frequency:
50Hz only)
SYNC. SYSTEM
• Check if the lens are stained. If dirty, clean the lens
with soft, clean cloth.
The image on the
screen is dim.
PICK-UP DEVICE
768(H) 582(V)1/3” BW CCD
752(H) 582(V)1/3” BW CCD
2:1 Interlace
525Lines
2:1 Interlace
625Lines
SCANNING SYSTEM
The camera is
not work
properly, and the
surface of the
camera case is
hot.
• Check that you have connected the camera to a
proper power.
MINIMUM ILLUMINATION
RESOLUTION
0.05 Lux at F1.2
570(H)TV Lines
– AC 24V, 60Hz
– AC 24V ~, 50Hz
– AC 230V ~, 50Hz
: BW-4302EA
: BW-4302CA
: BW-4302CH
VIDEO OUTPUT
1.0 Vp-p EIA Comp.
1.0 Vp-p CCIR Comp.
Center/Full Selectable
Backlight Compensation
IRIS MODE
VIDEO/ESC/DC Selectable
1/60~1/100,000 Sec
ELECTRONIC IRIS
The contrast on • Adjust the contrast feature of the monitor. If the
C/CS MOUNT Changeable
LENS
GAMMA CORRECTION
AGC
the screen is too
weak.
camera is exposed under too strong light, change the
camera position.
0.45
Built-in 28dB
Built-in
The image on the
screen flickers.
• Does the camera face to directly to the sun or
fluorescent lighting? Change the camera position.
APERTURE CORRECTION
S/N RATIO
50dB
• Check that you have used 50Hz (CCIR models) and
60Hz (EIA models) in linelock (L.L) mode. If the power
frequency is out of 50Hz (CCIR models)
/60Hz (EIA models), the linelock(L.L) synchronization
mode cannot be used. Use the Synchronization Mode
to INT mode.
AMBIENT TEMPERATURE
DIMENSION
-10
+50
14
122
The image on the
screen is
distorted.
55(W) 57(H) 136(L)mm(Without Lens)
440g(Without Lens) 450g(Without Lens) 500g(Without Lens)
IRIS JACK, MANUAL, L-WRENCH
WEIGHT
ACCESSORY
B W CCD CAMERA
25
24 B W CCD CAMERA
M EM O
DECLARATION OF CONFORMITY
Application of Council Directive(s)
Manufacturer's Name
Manufacturer's Address
89/336/EEC
SAMSUNG TECHWIN CO., LTD
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment
Model Name
Black & White CCD CAMERA
BW-4302CA/BW-4302CH
M1120001
Beginning Serial NO.
Year of Manufacture
Conformance to
2001
EN 60065
EN 55 013
EN 50 082-1
We, the undersigned, hereby declare that the equipment specified above
conforms to the above Directive(s).
Manufacturer SAMSUNG TECHWIN CO., LTD
Signature
Legal Representative in Europe
Signature
Full Name
Position
Place
YOUNG TAEK SON
Full Name
QUALITY CONTROL MANAGER Position
CHANGWON, KOREA
2001. 12. 1
Place
Date
Date
26 B W CCD CAMERA
|